General-machine-products 70524 Adams CD3 Continuous Duty Winch User Manual

AK 7/18/2012 ver 5 General Machine Products Company, Inc. 3111 Old Lincoln Highway Trevose, PA 19053 USA Tel: +1 215 357 5500 Fax: +1 215 357 6216 E

AK 7/18/2012 ver 5 The importance of cleanliness during installation cannot be over-emphasized. ♦ Caliper Drag Brakes on Adams Winches may be specifi

AK 7/18/2012 ver 5 The pressure from either side of the motor can release the brake. This feature enables the winch to pull in as well as power out. T

AK 7/18/2012 ver 5 Likewise, when the winch is not in operation, attach the winch line quick hook to a solid member on the tail shelf and slowly take

AK 7/18/2012 ver 5 ♦ Check the hydraulic system reservoir to make certain that it is filled to the correct level with the proper grade of oil. ♦ Mak

AK 7/18/2012 ver 5 If the winch has not been used for an extended period of time, inspect the interiors of the drive housing and final drive housing f

AK 7/18/2012 ver 5 Grease fittings and oil cups on the levelwind should be serviced every seventy-five (75) hours of operation. Apply a coat of engin

AK 7/18/2012 ver 5 Motor/Full Load Brake / Shuttle Valve Locator Item # Description Qty. A 26100 Motor, Two-section Hydraulic 1 B 25654 Fitting

AK 7/18/2012 ver 5 Drum Guard Locator Item # Description Qty. A 26262 Guard, Drum (Gear Box Side) 1 B 26263 Guard, Drum (Hanger Side) 1 C 2626

AK 7/18/2012 ver 5 A B C L Q R R C B E F H K G O M N J P Key P/N Description Qty A 25677 Air Cylinder 1 B 27447 Air cylinder Mounting Bracket 1

AK 7/18/2012 ver 5 19 Loc P/N Description Qty A 25677 Air cylinder 1 B 27447 Bracket 1 C 27443 Elbow 3 D 27337 Barb 6 E 27444 Adaptor 3 F

AK 7/18/2012 ver 5 TABLE OF CONTENTS SCOPE ...

AK 7/18/2012 ver 5 20

AK 7/18/2012 ver 5 21

AK 7/18/2012 ver 5 22

AK 7/18/2012 ver 5 23 23

AK 7/18/2012 ver 5 24

AK 7/18/2012 ver 5 Model CD3 Winch Specifications No other winch available anywhere offers you the same time-tested, rugged performance as the Adams

AK 7/18/2012 ver 5 Addendum: How to secure winch cable to drum Remove hitch pins 22 on upper and one lower roller. Pull out pin 20 and remove roller

AK 7/18/2012 ver 5 27 This Page Intentionally Left Blank

AK 7/18/2012 ver 5 GMP LIMITED WARRANTY 1a. General Machine Products Co., Inc. ("GMP") warrants to the purchaser and/or end user: (1) t

AK 7/18/2012 ver 5 the responsibility of GMP, and are not covered by this Warranty. 3f. Incidental repair charges incurred by an authorized GMP deal

AK 7/18/2012 ver 5 SCOPE - This document contains information pertinent to the Installation, Operation and Maintenance of the Adams® Model CD3 Continu

AK 7/18/2012 ver 5 winch. The brake disc rotor is mounted at the factory on the clutch end drum flange. The remote actuator, reservoir, and flexible

AK 7/18/2012 ver 5 The maximum allowable pull of the standard drum shaft extension is 1,500 pounds (6,7 kN) using a standard 7 in. (18 cm) diameter ca

AK 7/18/2012 ver 5 Wire rope (winch line) may be old, damaged or weakened by such defects as kinks, cuts, extreme bends or loops. Such conditions are

AK 7/18/2012 ver 5 CAUTION - DO NOT WELD THE MOUNTING BRACKETS TO THE CHASSIS FRAME. All of the mounting hardware and the drum shaft extension are sh

AK 7/18/2012 ver 5 8 Recommended hydraulic line diameters are: ♦ Pump to control valve: 1¼ in. (32 mm) ♦ Control valve to tank: 1¼ in. (32 mm) ♦

AK 7/18/2012 ver 5 are magnetically activated and while they work on the same principle as Hall effect sensors, they are exceedingly sensitive. The s